Leveling Mount

Part # J-16461-4

LORD Leveling Mounts help level equipment.

Additional Images

Lets Get Started!  

Quick Quote
Ask A Question
Engineering Support

Max Axial Load

1000 lbs. / 4448 N

Adjusting Bolt 1/2-13UNC x 5" / 127 mm
Weight 2.5 lbs. / 1.1 kg
Elastomer Neoprene Compounded to resist oil, ozone & caustic material
Part No. J-16461-4 | J164614
Manufacturer LORD Corporation
Part Category Vibration Control
Part Section Machinery Mounts
Part Type Leveling Mounts
Part Status
Call +1 800 657-0747 or use the
webform to the right on this page
Part Alternative
Call +1 800 657-0747  or use the
webform to the right on this page


Catalog Page No.
Catalog Section Page No.
Rubber Parts Catalog Machinery Mounts Page 10
LORD PC7000 Plateform Mounts Page 46
LORD PC-2201m Plateform Mounts Page 44




Dimensions - Under No Load Technical Drawing
Dimension Measurement Notes
Bolt 1/2-10UNC x 5" / 127 mm  
D 4-3/4" in. / 120.7 mm  
H 1-1/2 in. / 38.1 mm Height (Free)

NOTES: Red figures are metric reference.


***Notes only apply if called out in table***




Vertical natural frequency under maximum load: 12 Hz.

Maximum adjustment is 1/2" (12.7 mm). Do not exceed this amount.

Metal housing made of high strength steel - high visibility yellow paint (OSHA approved).

Elastomer: neoprene compounded to resist oil, ozone and caustic material.


Before installing, be sure the mounts are the right ones for your machine.

  1. Remove adjusting bolt and lock nut from mount.
  2. Raise machine and slide mount under foot.
  3. Insert adjusting bolt through clearance hole in foot and engage threads in mount.
  4. Lower machine onto mounts
  5. Turn bolt until it bottoms.
  6. TO LEVEL - Level machine by turning the adjusting bolt.
  7. Tighten lock nut against machine base.


Adjustment bolt and lock nut included.

Vibration Problems

LORD Machinery Mounts are specifically engineered to isolate vertical shocks and reduce transmission of structural noise through floors. If your application involves intermittent or continuous vibration frequencies above or below 600 cycles per minute, the follow applies -

  • Vibration frequencies above 600 cycles per minute, use LORD Chan-L Mounts
  • Vibration frequencies below 600 cycles per minute are involved, use LORD Lattice Mounts

Custom Designs

Customized designs and special elastomer compounds for specific problems are available. These may result in spring rates and dimensions other than shown.

A part’s listing on this website does not guarantee its availability.



Custom Parts

Our custom molding department can make a part just for your application.


Would you like some assistance in selecting the right mount for your application?  Our engineering department can help.  Please call or use the webform below.  We will be glad to assist.

Not what you are looking for?

Our knowledgeable staff can assist you with whatever you need.  From Special Packaging, Overnight shipments to applications engineering. DeltaFlex is ready to help find a solution.

Engineering Assistance

"Frequently vibration isolation problems require a system engineering analysis..." - Put us to work for you.

DeltaFlex has the computer capability, as well as specialized programs, for analyzing engine/transmission combinations. The output from these analyses is a mounting proposal which optimizes performance over the complete range of operating speeds. This service is available to you upon request. If you require this type of engineering assistance please call 800.657.0747 we will be glad to assist you.

What is the impact of Vibration Control?

The biggest impact that vibration isolation can have, is with the end users of our customers products, more importantly their perception of the quality of those products.

Values states herein represent typical values as not all test are run on each lot produced. For formalized product specifications or specific product end uses, contact Customer Service 262.632.2345.

A part’s listing on this website does not guarantee its availability.